Instruments & Meters

SinceVision Launches SGI-N030W Wide-Spot Laser Displacement Sensor

The SGI-N030W targets stable micrometre-level measurement on textured surfaces, with in-line battery electrode thickness inspection among its cited uses.

Zorica IlicNovember 17, 20265 min read0 views

Two wide-spot laser sensor heads face a moving metallic web on a precision gantry in a clean industrial setting, with a soft blue measurement plane crossing the material.

SinceVision has introduced the SGI-N030W, a wide-spot laser displacement sensor intended for high-speed, non-contact dimensional measurement on rough, textured and irregular surfaces. The company says the new model extends its SGI Series and is aimed at lithium-ion battery production, semiconductor processing and precision mechanical engineering, where micrometre-level measurements must remain reliable across varying surface finishes.

The design addresses a common problem with conventional point-spot laser sensors. Those devices concentrate reflected laser energy on a small area, so scratches, grain boundaries, brushed textures and matte finishes can create signal changes that are mistaken for dimensional movement. In production, such variations may trigger false defect warnings and additional manual inspection. The SGI-N030W uses a wider optical spot and optical triangulation to collect reflected light from a larger surface area. The sensor averages microscopic peaks and valleys before converting the signal, which the company says reduces the influence of surface roughness and optical scattering. SinceVision identifies drawn metals, sandblasted surfaces and coated battery foils as materials that can benefit from this approach.

Specified performance and interfaces

The sensor has a 30 mm reference distance and a ±5 mm measurement range. SinceVision specifies repeatability of 0.05 µm on a diffuse white target under static conditions and linearity of ±0.02% of full scale across the range. A sampling frequency of 50 kHz, equivalent to a 20 µs update interval, is intended to support high-speed measurement and monitoring of dynamic processes. Communication options include RS485, 100Base-TX Ethernet and switchable analogue outputs for 4–20 mA current or 0–10 V voltage signals. Master-slave synchronisation also allows two sensors to face each other and measure opposite sides of a component or moving material at the same time.

Battery electrode thickness measurement

One of the main applications cited by SinceVision is in-line thickness measurement of lithium-ion battery electrodes. Coating thickness and uniformity affect energy density, internal resistance and long-term cell stability. Conventional offline checks with contact micrometers or drop indicators can depend on operator technique and may deform wet or uncured electrode material. Periodic spot checks also cannot provide continuous coverage of coating variation across a full production reel.

In the proposed inspection setup, two synchronised sensors sit above and below a moving electrode web. They are mounted on a calibrated, low-thermal-expansion marble gantry and measure the clearance to each side of the material. A controller combines those readings with the fixed mounting datum to calculate absolute electrode thickness in real time. SinceVision reports that production trials achieved stable, repeatable thickness measurement within ±0.3 µm at a web speed of 300 mm/s. The 50 kHz sampling rate provides longitudinal resolution for detecting local coating agglomerations, edge thinning and exposed substrate before the material reaches cell winding.

Semiconductor and precision assembly uses

The sensor is also intended for semiconductor manufacturing, where non-contact operation matters when handling sensitive wafer surfaces. Potential tasks include wafer position verification, edge detection, height measurement, and checks of wafer seating and chuck alignment in atmospheric transfer modules and vacuum load-lock systems. In precision assembly, the sensor can monitor voice coil motors, linear actuators and micro-steppers. Its sampling rate is intended to capture transient displacement, mechanical oscillation, settling behaviour and end-stop overshoot across the full measurement range. Position data can go to machine control systems over Ethernet for real-time monitoring and process control.

Company view on surface-related errors

Jack Li, Global Sales and Marketing Director at SinceVision, says false defect warnings caused by surface texture remain a recurring challenge in battery manufacturing and precision assembly. He says conventional point-beam laser sensors can read microscopic scratches and rough coatings as actual thickness changes, slowing production lines and creating demand for extra manual inspection. According to Li, the SGI-N030W’s expanded optical spot is designed to average out those surface-related variations, while synchronisation between opposing sensor heads supports high-speed thickness verification.